The newly updated leads4pass 300-610 dumps contain 203 exam questions and answers, as well as provide difficult analysis, in line with the Cisco 300-610 DCID certification exam conditions!
Because leads4pass 300-610 dumps are actually verified by a professional team, it is real and effective! And provide two learning types: 300-610 dumps PDF, and 300-610 dumps VCE, both types contain the latest 300-610 exam questions!
So, get the latest 300-610 dumps in PDF or VCE format from leads4pass: https://www.leads4pass.com/300-610.html, to ensure you pass the exam easily.
Two free surprises:
- Get some leads4pass 300-610 dumps in PDF format
- Online practice section leads4pass 300-610 dumps
First Surprise: Online Download Section leads4pass 300-610 dumps: https://drive.google.com/file/d/15jAJCTDbGKLeqYMR90ubZ-ZlCIS3WzC3/
The second surprise: online practice part leads4pass 300-610 dumps
| Type | Number of exam questions | Exam name | Exam code |
| Free | 15 | Designing Cisco Data Center Infrastructure (DCID) | 300-610 |
Question 1:
A Cisco UCS chassis with several blade servers, a pair of IOMs, and a pair of Cisco UCS Fabric Interconnects are installed in a data center. Which two high-availability architectures are recommended between the IOMs and fabric interconnects? (Choose two.)
A. One, two, four, and eight links are supported to be used between each IOM and fabric interconnect.
B. IOM is connected to the fabric interconnect that is acting as fabric A. and IOM B is connected to the fabric interconnect that is acting as fabric B.
C. Any combination of one to eight links are supported to be used between each IOM and fabric interconnect.
D. The lOMs are connected with multiple straight and cross-connect links toward a pair of nonclustered fabric interconnects.
E. Straight and cross-connect links should be used between the lOMs and fabric interconnects to offer higher availability.
Correct Answer: CD
Question 2:
A set of virtual machines must be live migrated from a data center to a disaster recovery site. The data center and disaster recovery sites are connected through an Inter-Pod Network topology. The gateway address of the virtual machine is the same across the data center and disaster recovery. Which Cisco Nexus feature supports this requirement?
A. VXLAN EVPN
B. FabricPath
C. FHRR
D. VPLS
Correct Answer: A
Question 3:
Which two configurations are available by using a service profile template in Cisco UCS Manager? (Choose two.)
A. number of vHBAs
B. ARP entries
C. UUID assignment
D. VXLAN membership
E. target server
Correct Answer: AC
Reference:
Question 4:
An engineer is designing a disaster recovery solution. In the event of a node failure, the solution should either direct all of the traffic to another node or load-balance the traffic across the remaining nodes. Which solution should be implemented in the design?
A. cold standby
B. warm standby
C. active/active
D. active/passive
Correct Answer: C
Question 5:
An engineer is installing a Cisco Nexus 7000 Series Switch with F2-Series I/O Module. The company\’s strict security policy requires that the port be in-band. The engineer must also keep these
considerations in mind:
The customer\’s security requirements mandate the use of a secure management mechanism that supports authentication and encryption.
The port should support management over IP.
Which port type must be used to meet these requirements?
A. management port
B. console port
C. connectivity management port
D. Ethernet port
Correct Answer: B
Question 6:
An engineer manages hundreds of Cisco Nexus Series and 9000 Series Switches that are installed at several data centers and wants to use one of the built-in automation tools of the Cisco NX-OS Guest Shell to automate daily activities. The engineer requires a tool that uses imperative language, has extensive support, and is object-oriented. Which automation tool should be used to meet these requirements?
A. Phython
B. Bash
C. YAML
D. Perl
Correct Answer: A
Explanation: Python is an object-oriented and imperative language. YAML is declarative.
Question 7:
A network consultant reviews the requirements for the Storage Area Network (SAN) design. The proposed solution must offer very efficient port usage and eliminate the need for a separate physical layer of switches and their associated ISLs. The design is not expected to require future expansion.
Which SAN topology must be used to meet these requirements?
A. core-edge
B. collapsed-core
C. core-distribution-access
D. edge-core-edge
Correct Answer: B
Question 8:
An engineer must design a VXLAN EVPN network. The solution should optimize broadcast, unknown unicast, and multicast (BUM) and short BUM replication, and use PIM anycast RP. Which solution should be included in the design?
A. PIM sparse mode
B. ingress replication
C. head-end replication
D. PIM dense mode
Correct Answer: A
Question 9:
A network architect designs the iSCSI-based storage area network solution. The iSCSI datastore must be designed with high availability, minimal downtime, and no single point of failure. The requirement is to fail over I/O to alternate paths based on SCSI sense codes without reliance on network failures.
Which feature must be deployed to meet these requirements?
A. hardware-based flow control
B. port security
C. iSCSI multipath
D. NIC teaming
Correct Answer: C
Question 10:
Refer to the exhibit.
Which template is used when a vHBA template pair is created for a specific server that inherits its attributes from an existing template?
A. Secondary
B. Initial
C. Updating
D. Primary
Correct Answer: B
Question 11:
An engineer wants to eliminate the manual process of checking the system hardware and firmware against a specified hardware compatibility tool. The tool must be able to manage an extensive list of devices including Cisco HyperFlex, MDS, and Nexus switches. The tool must manage hardware in multiple data centers so it should be deployed on public cloud infrastructure. Which tool meets these requirements?
A. Cisco intersight
B. Cisco UCS director
C. Cisco data center network manager
D. Cisco tetration
Correct Answer: A
Question 12:
A customer requires a tool to manage Cisco network hardware. The solution must use secure communication using a secure network protocol, support the use of declarative language to manage the state of resources, and periodically pull changes to the controlled nodes. Which tool meets these requirements?
A. Ansible
B. SaltStack
C. Puppet
D. Nomir
Correct Answer: C
Question 13:
After experiencing traffic disruptions from the failure of a single router, a customer asks an engineer to design a solution that will prevent this from occurring in the future. While examining the customer\’s environment, the engineer discovers that the routers are manufactured by a variety of different vendors, and they have varying amounts of CPU and memory resources. Additionally, several of the customer\’s applications require the ability to fine-tune the load-balancing parameters between multiple routers. Which solution should be used to meet these requirements?
A. VRRP
B. GLBP
C. FHRP
D. HSRP
Correct Answer: A
Explanation: Load balancing can be done by having different VRRP groups and configuring different servers with different default gateways. HSRP and GLBP are Cisco proprietary.
Question 14:
Which two automation requirements can be met by using Puppet? (Choose two.)
A. Push configuration updates immediately to servers.
B. Enable clients to pull changes to configuration files.
C. Enable clients to pull changes without installing an agent.
D. Provide support for writing new modules in Python.
E. Enable one-off infrastructure changes to be performed manually.
Correct Answer: AB
https://blogs.cisco.com/datacenter/cisco-nx-os-and-puppet-agentless-data-center-automation
Question 15:
An engineer must use OTV for layer 2 connectivity between data centers to support virtual machines between the customer sites. To support this requirement, the engineer must ensure the existence of the same default gateway on both sites. Additionally, the operations team reports high bandwidth utilization on site A and wants to optimize the outbound traffic flows to use a DC exit point. Which feature must be used to meet this requirement?
A. FHRP filter
B. Control group
C. Data Group
D. ARP filter
Correct Answer: A
Enjoy two premium benefits for free! Although they are only part of the leads4pass 300-610 dumps!
Now, use PDF or VCE to practice leads4pass 300-610 dumps: https://www.leads4pass.com/300-610.html (203 Q&A), assisting you to pass the Cisco 300-610 DCID certification exam 100% successfully.